Aggiungere alla lista dei desideri
Togliere una barca dalle preferite
boatDetail
boatDetail
0
bid=s231204
bid=s231204
s231204
5
Classic 50FT Steel Cutter (barca a vela) - vendita
barca a vela / yacht a vela, barca usataImmagini
1 / 41
▶
▶
immagini
stampa
condividi
Descrizione +
Remarks :
Classic 50ft steel cutter for sale in Kent:
Artic Explorer is a classic 50ft steel cutter that is currently berthed in Chatham Marina. She was built in 1982 as an ocean going steel vessel with a cutter rig to a designed by Alan Mummery. This yacht has undergone an extensive refit over the past 4 years and is ready to go ocean sailing. It has 7 berths ,a comfortable living area and is powered by a Yanmar 4JH3E (2002) 56 HP diesel engine with a shaft drive to a 3 bladed folding propeller .This boat boasts all the navigation and deck gear you would expect for a ocean going vessel and is ready to set sail. This vessel is UK Vat paid and the owner is willing to delivery to Northern Europe or anywhere in the UK
Accommodation :
This 50ft steel cutter provides berths for up to six people in 3 cabins, with a double cabin to aft portside and a large single berth to starboard.
Forward is a large double berth with a large opening deck hatch which gives lots of light and makes the cabin feel very airy. The large concealed bar features a solid mahogany folding dining table with removable fiddles and sofa chairing.
The seating can also be used to provide two further berths. These berths have appropriate tailored lee-cloths. There is a roomy navigation area with navigators chair and full sized navigation station desk with both red and white lights and under-table storage for navigation books etc.
The galley is to port and has a seamless stainless steel worktop and has a pair of sinks with pressurised hot and cold water . Hot water heated by the engine and via a 240v immersion heater. There is a three burner stove with oven and grill.
There is a large heads compartment with marine toilet with a featured teak wash basin (new 2023) with shower and hot/cold mixer tap and multiple storage lockers and handholds throughout. The yacht has wide side decks which provide a real sense of safety when walking around deck.
The companion way steps lead up to the large and very secure cockpit which has a sold doghouse and lots of storage lockers.
Inventory :
Deck Equipment: 2 X 55lb CQR Anchors
60m of 10mm anchor chain
100m of anchor warp
Danforth Kedge Anchor with 40m of chain and 30m of warp
Electric Windlass
Danbuoys x 2
Horseshoe buoys x 2
Liferaft 6 person (new 2016 needs a service)
Fenders x 6
Mooring Warps x6
10ft Aluminium rib with 15hp outboard by separate negotiation
Navigation Equipment: Chart Plotter - Raymarine C90W with electronic charts European/Caribbean
AIS Receiver/Transponder -Raymarine
Depth - Raymarine
Speed/log -Raymarine
Wind -Raymarine
Autopilot - Raymarine
Fleming Ocean 60 wind vane
SSB (New SSB Antenna 2023)
VHF/DSC M323 ( New in 2022) with command mic
ST60 Iridium Go Satellite phone
New Mast Antenna
Furuno Radar
Safety Equipment: Fire Extinguishers x 4
Radar Reflector
EPIRB
Liferaft 6 person in need of a service
Jack Stays
Manual Bilge pump x 1
Electric Bilge pumps x 2
Keel:
Traditional long keel with tiller steering
History and Construction:
Artic Explorer Designed by Alan Mummery is a 50ft steel hull, cutter rig fin keel ocean going yacht. This yacht has had a major refit in the past four years getting her ready to complete in the next ARC. In 2017 the under went a full face lift including a re-paint of the hull and topsides, some new seacocks, new prop, new prop shaft new engine mounts and lots more. Unfortunately after all of this preparation for the adventure of a lifetime ill health is preventing the owner participating and hence why she is being advertised for sale
Mechanical :
Sails and Spars
The rigging on board this Alan Mummery Steel Cutter includes a twin spreader 15m aluminium mast, with new 2022 twin running backstays and spare masthead sheaves. There are heavy duty 'granny bars' at the mast and it has mast steps to the top of the mast. A heavy duty bowsprit features twin rollers and a steel rod bobstay; there is also a spinnaker and jockey pole with sheets and guys.
Nearly all of the running rigging is new, with ample spare ropes onboard, including Lewmar reefing lines. There are also 2016 Jackstays and Lazy jacks.
There is an extensive sail wardrobe which includes: two mainsails - one fully battened, three reef, slab reefed to cockpit; three genoas - one high cut and one in bright orange made in 2021 with Arctic Explorer name and logo on it ; staysail; two spare Yankee genoas; storm staysail (hank on); cruising chute; spinnaker with new sheets and guys
The deck of this Steel Cutter features a Heavy duty doghouse with reefing lines and main halyard led inside.
Winches:
Wilkins two-speed 26mm primary winches;
Harken 16mm secondary winches;
Lewmar winch for reefing lines in cockpit;
Barlow 26 mainsheet winch in cockpit;
Two mast winches; and one outhaul winch on boom. There are also a full suit of rope clutches
Sails:
Mainsail, Hood Thorn burrow - Slab (2002) Stack Pack, Fully Battened, 3 Reefs
Headsail Thorn burrow - Furling (2002)
Tri Sail (Unknown Year)
Cutter (2009)
Storm Jib (Unknown Year)
Spinnaker (Unknown Year)
Cruising Chute (2010)
2 x Genoas (2002) and (2021)
Mechanical Systems:
This Steel Cutter is powered by a Yanmar 4JH3E 56hp diesel engine.(2002) The boat is shaft driven to a 3 bladed folding propeller .Fuel tank capacity is 380 litres in one mail tank and stowage for 10 external fuel cans .It has a cruising speed 7 knots and approximate max speed of 10.4 knots . the engine has completed 3165 hours as 1st August 2023. The engine has twin alternators.
The yacht is fitted with a 2016 Pordesk IKW 240V Genset new in 2021 with approx. 20 hours usage and a PUR Survivor water maker.
Electrical Systems:
The yacht has 4 x 12v 220AH gel batteries that were fitted new in April 2017 It has LED lighting and a number of 12v sockets throughout It has a VIctron 2kW battery charger and management system. There are 2 x 1kW movable solar panels and Victron triple MPPT charge controller and galvanic isolator. It has a 240v shore ring main system with RCD breakers, with fresh long run potential cords and new diodes, There is a pair of 100W swing mounted solar panels with a separate EP solar regulator and control display.... testo completo
Classic 50ft steel cutter for sale in Kent:
Artic Explorer is a classic 50ft steel cutter that is currently berthed in Chatham Marina. She was built in 1982 as an ocean going steel vessel with a cutter rig to a designed by Alan Mummery. This yacht has undergone an extensive refit over the past 4 years and is ready to go ocean sailing. It has 7 berths ,a comfortable living area and is powered by a Yanmar 4JH3E (2002) 56 HP diesel engine with a shaft drive to a 3 bladed folding propeller .This boat boasts all the navigation and deck gear you would expect for a ocean going vessel and is ready to set sail. This vessel is UK Vat paid and the owner is willing to delivery to Northern Europe or anywhere in the UK
Accommodation :
This 50ft steel cutter provides berths for up to six people in 3 cabins, with a double cabin to aft portside and a large single berth to starboard.
Forward is a large double berth with a large opening deck hatch which gives lots of light and makes the cabin feel very airy. The large concealed bar features a solid mahogany folding dining table with removable fiddles and sofa chairing.
The seating can also be used to provide two further berths. These berths have appropriate tailored lee-cloths. There is a roomy navigation area with navigators chair and full sized navigation station desk with both red and white lights and under-table storage for navigation books etc.
The galley is to port and has a seamless stainless steel worktop and has a pair of sinks with pressurised hot and cold water . Hot water heated by the engine and via a 240v immersion heater. There is a three burner stove with oven and grill.
There is a large heads compartment with marine toilet with a featured teak wash basin (new 2023) with shower and hot/cold mixer tap and multiple storage lockers and handholds throughout. The yacht has wide side decks which provide a real sense of safety when walking around deck.
The companion way steps lead up to the large and very secure cockpit which has a sold doghouse and lots of storage lockers.
Inventory :
Deck Equipment: 2 X 55lb CQR Anchors
60m of 10mm anchor chain
100m of anchor warp
Danforth Kedge Anchor with 40m of chain and 30m of warp
Electric Windlass
Danbuoys x 2
Horseshoe buoys x 2
Liferaft 6 person (new 2016 needs a service)
Fenders x 6
Mooring Warps x6
10ft Aluminium rib with 15hp outboard by separate negotiation
Navigation Equipment: Chart Plotter - Raymarine C90W with electronic charts European/Caribbean
AIS Receiver/Transponder -Raymarine
Depth - Raymarine
Speed/log -Raymarine
Wind -Raymarine
Autopilot - Raymarine
Fleming Ocean 60 wind vane
SSB (New SSB Antenna 2023)
VHF/DSC M323 ( New in 2022) with command mic
ST60 Iridium Go Satellite phone
New Mast Antenna
Furuno Radar
Safety Equipment: Fire Extinguishers x 4
Radar Reflector
EPIRB
Liferaft 6 person in need of a service
Jack Stays
Manual Bilge pump x 1
Electric Bilge pumps x 2
Keel:
Traditional long keel with tiller steering
History and Construction:
Artic Explorer Designed by Alan Mummery is a 50ft steel hull, cutter rig fin keel ocean going yacht. This yacht has had a major refit in the past four years getting her ready to complete in the next ARC. In 2017 the under went a full face lift including a re-paint of the hull and topsides, some new seacocks, new prop, new prop shaft new engine mounts and lots more. Unfortunately after all of this preparation for the adventure of a lifetime ill health is preventing the owner participating and hence why she is being advertised for sale
Mechanical :
Sails and Spars
The rigging on board this Alan Mummery Steel Cutter includes a twin spreader 15m aluminium mast, with new 2022 twin running backstays and spare masthead sheaves. There are heavy duty 'granny bars' at the mast and it has mast steps to the top of the mast. A heavy duty bowsprit features twin rollers and a steel rod bobstay; there is also a spinnaker and jockey pole with sheets and guys.
Nearly all of the running rigging is new, with ample spare ropes onboard, including Lewmar reefing lines. There are also 2016 Jackstays and Lazy jacks.
There is an extensive sail wardrobe which includes: two mainsails - one fully battened, three reef, slab reefed to cockpit; three genoas - one high cut and one in bright orange made in 2021 with Arctic Explorer name and logo on it ; staysail; two spare Yankee genoas; storm staysail (hank on); cruising chute; spinnaker with new sheets and guys
The deck of this Steel Cutter features a Heavy duty doghouse with reefing lines and main halyard led inside.
Winches:
Wilkins two-speed 26mm primary winches;
Harken 16mm secondary winches;
Lewmar winch for reefing lines in cockpit;
Barlow 26 mainsheet winch in cockpit;
Two mast winches; and one outhaul winch on boom. There are also a full suit of rope clutches
Sails:
Mainsail, Hood Thorn burrow - Slab (2002) Stack Pack, Fully Battened, 3 Reefs
Headsail Thorn burrow - Furling (2002)
Tri Sail (Unknown Year)
Cutter (2009)
Storm Jib (Unknown Year)
Spinnaker (Unknown Year)
Cruising Chute (2010)
2 x Genoas (2002) and (2021)
Mechanical Systems:
This Steel Cutter is powered by a Yanmar 4JH3E 56hp diesel engine.(2002) The boat is shaft driven to a 3 bladed folding propeller .Fuel tank capacity is 380 litres in one mail tank and stowage for 10 external fuel cans .It has a cruising speed 7 knots and approximate max speed of 10.4 knots . the engine has completed 3165 hours as 1st August 2023. The engine has twin alternators.
The yacht is fitted with a 2016 Pordesk IKW 240V Genset new in 2021 with approx. 20 hours usage and a PUR Survivor water maker.
Electrical Systems:
The yacht has 4 x 12v 220AH gel batteries that were fitted new in April 2017 It has LED lighting and a number of 12v sockets throughout It has a VIctron 2kW battery charger and management system. There are 2 x 1kW movable solar panels and Victron triple MPPT charge controller and galvanic isolator. It has a 240v shore ring main system with RCD breakers, with fresh long run potential cords and new diodes, There is a pair of 100W swing mounted solar panels with a separate EP solar regulator and control display.... testo completo
chiudere la selezione
Dati della barca +
Dati della barca Classic 50FT Steel Cutter
Prezzo:
£ 99.950
(≈ € 116.706)
IVA inclusa
ID barca:
s231204
Modello di barca:
Classic 50FT Steel Cutter
Produttore:
Tipo di barca:
barca a vela
Categoria di barca:
yacht a vela
Categoria:
barca usata
Anno di costruzione:
1982
Posto d’ormeggio:
Gran Bretagna, Chatham Marina, Kent
Materiale dello scafo:
barca in acciaio
Dettagli tecnici
Lunghezza:
15,24 m (50 piedi)
Larghezza:
3,66 m
Motore:
Yanmar 4JH3E (2002)
Potenza del motore:
56 cv (41 kW)
Carburante:
diesel
chiudere la selezione
Pubblicità / servizio
Attrezzatura+
Attrezzatura - Classic 50FT Steel Cutter - yacht a vela / barca a vela in vendita
Navigazioneautopilota, plotter, radar, vhf
Equipaggiamento tecnico
caricabatterie
Sicurezza
EPIRB, pompa di sentina elettrica, pompa di sentina manuale, zattera di salvataggio
Dotazioni di coperta
parabordi
Dotazioni degli interni
barbecue, lavandino
Vele
spinnaker
chiudere la selezione
Contatto-
Classic 50FT Steel Cutter - ottenere informazioni del venditore senza impegno
pf-21790
La preghiamo di comunicare al venditore che ha trovato questa offerta su Yachtall.
Contatto:
Band of Boats
Network Yacht Brokers Kent
Chatham Maritime Marina, Leviathan Way Chatham
ME4 4LP Kent
Gran Bretagna
Telefono:
mostrare
Lingue:
inglese, francese
Da 4 anni su yachtall.com
chiudere la selezione
Comprare una barca:
Custom built/Eigenbau barche yacht a vela barche a vela in vendita barche a vela Gran Bretagna barche usate barche usate Custom built/Eigenbau barche in acciaio
Custom built/Eigenbau barche yacht a vela barche a vela in vendita barche a vela Gran Bretagna barche usate barche usate Custom built/Eigenbau barche in acciaio
Altre barche (come p.e. un(o) Classic 50FT Steel Cutter) - compra e vendita
Custom built Foiler 50
Barca a vela / trimarano a vela: Custom built/Eigenbau, barca usataLunghezza x larghezza: 15,24 m x 11,89 m, 15,24 x 11,89 m anno: 1983
€ 70.000
Posto d’ormeggio: Sint Maarten, Caribbean
1983
Azienda: Band of Boats
Prezzo: € 70.000, IVA esclusa
Rinaldi ARIA 142
Barca a vela / sloop: Custom built/Eigenbau, barca usataLunghezza x larghezza: 14,20 m x 4,53 m, 14,20 x 4,53 m anno: 2003, cabine: 4
Motore: 96 cv (71 kW), diesel
€ 100.000
Posto d’ormeggio: Italia, Santa Teresa Gallura
2003
Azienda: Band of Boats
Prezzo: € 100.000, IVA inclusa
Steel Sailboat 50
Barca a vela / yacht a vela: Custom built/Eigenbau, barca usata, barca in acciaioLunghezza x larghezza: 15,24 m x 4,30 m, 15,24 x 4,30 m anno: 1991
Motore: TMD41A, 150 cv (110 kW), diesel
kr. 1.550.000
Posto d’ormeggio: Danimarca, Svendborg
1991
Azienda: Band of Boats
Prezzo: kr. 1.550.000 (≈ € 207.851), IVA esclusa
Classique YAWL Bermudien
Barca a vela / iolla: Custom built/Eigenbau, barca d’epocaLunghezza x larghezza: 15,05 m x 3,79 m, 15,05 x 3,79 m anno: 1964, cabine: 2
Motore: Yanmar 4JH4HTI, 110 cv (81 kW), diesel
€ 270.000
Posto d’ormeggio: Francia, Marseille
1964
Azienda: Band of Boats
Prezzo: € 270.000, IVA inclusa
Questi(e) barche a vela Le potrebbero piacere
Gulet Caicco ECO 155 (15 m) Custom built 50' Yawl (15,24 m) Custom built Schooner (14,90 m) Beasley & KEMP (15,10 m) 50 Feet Aluminium Catamaran (14,95 m) Catamaran 15 M (15 m) Gulet Caicco ECO 310 (14,95 m) Custom built Caroff (14,17 m) Custom PLAN Caroff (14,17 m) Ketch Galeasen Jutta (16,20 m) Professional Catamaran (15 m) Van de Stadt 51 (15,53 m)Quale versione vorrebbe visualizzare?
Inviare una richiesta
Classic 50FT Steel Cutter, anno 1982
Contatto:
Band of Boats