Ajouter à la liste de souhaits
Supprimer le bateau de la liste des favoris
boatDetail
boatDetail
0
bid=s231204
bid=s231204
s231204
5
Classic 50FT Steel Cutter (voilier) à vendre
voilier / yacht à voile, bateau d'occasionImages
1 / 41
▶
▶
images
impression
partager
Description +
Remarks :
Classic 50ft steel cutter for sale in Kent:
Artic Explorer is a classic 50ft steel cutter that is currently berthed in Chatham Marina. She was built in 1982 as an ocean going steel vessel with a cutter rig to a designed by Alan Mummery. This yacht has undergone an extensive refit over the past 4 years and is ready to go ocean sailing. It has 7 berths ,a comfortable living area and is powered by a Yanmar 4JH3E (2002) 56 HP diesel engine with a shaft drive to a 3 bladed folding propeller .This boat boasts all the navigation and deck gear you would expect for a ocean going vessel and is ready to set sail. This vessel is UK Vat paid and the owner is willing to delivery to Northern Europe or anywhere in the UK
Accommodation :
This 50ft steel cutter provides berths for up to six people in 3 cabins, with a double cabin to aft portside and a large single berth to starboard.
Forward is a large double berth with a large opening deck hatch which gives lots of light and makes the cabin feel very airy. The large concealed bar features a solid mahogany folding dining table with removable fiddles and sofa chairing.
The seating can also be used to provide two further berths. These berths have appropriate tailored lee-cloths. There is a roomy navigation area with navigators chair and full sized navigation station desk with both red and white lights and under-table storage for navigation books etc.
The galley is to port and has a seamless stainless steel worktop and has a pair of sinks with pressurised hot and cold water . Hot water heated by the engine and via a 240v immersion heater. There is a three burner stove with oven and grill.
There is a large heads compartment with marine toilet with a featured teak wash basin (new 2023) with shower and hot/cold mixer tap and multiple storage lockers and handholds throughout. The yacht has wide side decks which provide a real sense of safety when walking around deck.
The companion way steps lead up to the large and very secure cockpit which has a sold doghouse and lots of storage lockers.
Inventory :
Deck Equipment: 2 X 55lb CQR Anchors
60m of 10mm anchor chain
100m of anchor warp
Danforth Kedge Anchor with 40m of chain and 30m of warp
Electric Windlass
Danbuoys x 2
Horseshoe buoys x 2
Liferaft 6 person (new 2016 needs a service)
Fenders x 6
Mooring Warps x6
10ft Aluminium rib with 15hp outboard by separate negotiation
Navigation Equipment: Chart Plotter - Raymarine C90W with electronic charts European/Caribbean
AIS Receiver/Transponder -Raymarine
Depth - Raymarine
Speed/log -Raymarine
Wind -Raymarine
Autopilot - Raymarine
Fleming Ocean 60 wind vane
SSB (New SSB Antenna 2023)
VHF/DSC M323 ( New in 2022) with command mic
ST60 Iridium Go Satellite phone
New Mast Antenna
Furuno Radar
Safety Equipment: Fire Extinguishers x 4
Radar Reflector
EPIRB
Liferaft 6 person in need of a service
Jack Stays
Manual Bilge pump x 1
Electric Bilge pumps x 2
Keel:
Traditional long keel with tiller steering
History and Construction:
Artic Explorer Designed by Alan Mummery is a 50ft steel hull, cutter rig fin keel ocean going yacht. This yacht has had a major refit in the past four years getting her ready to complete in the next ARC. In 2017 the under went a full face lift including a re-paint of the hull and topsides, some new seacocks, new prop, new prop shaft new engine mounts and lots more. Unfortunately after all of this preparation for the adventure of a lifetime ill health is preventing the owner participating and hence why she is being advertised for sale
Mechanical :
Sails and Spars
The rigging on board this Alan Mummery Steel Cutter includes a twin spreader 15m aluminium mast, with new 2022 twin running backstays and spare masthead sheaves. There are heavy duty 'granny bars' at the mast and it has mast steps to the top of the mast. A heavy duty bowsprit features twin rollers and a steel rod bobstay; there is also a spinnaker and jockey pole with sheets and guys.
Nearly all of the running rigging is new, with ample spare ropes onboard, including Lewmar reefing lines. There are also 2016 Jackstays and Lazy jacks.
There is an extensive sail wardrobe which includes: two mainsails - one fully battened, three reef, slab reefed to cockpit; three genoas - one high cut and one in bright orange made in 2021 with Arctic Explorer name and logo on it ; staysail; two spare Yankee genoas; storm staysail (hank on); cruising chute; spinnaker with new sheets and guys
The deck of this Steel Cutter features a Heavy duty doghouse with reefing lines and main halyard led inside.
Winches:
Wilkins two-speed 26mm primary winches;
Harken 16mm secondary winches;
Lewmar winch for reefing lines in cockpit;
Barlow 26 mainsheet winch in cockpit;
Two mast winches; and one outhaul winch on boom. There are also a full suit of rope clutches
Sails:
Mainsail, Hood Thorn burrow - Slab (2002) Stack Pack, Fully Battened, 3 Reefs
Headsail Thorn burrow - Furling (2002)
Tri Sail (Unknown Year)
Cutter (2009)
Storm Jib (Unknown Year)
Spinnaker (Unknown Year)
Cruising Chute (2010)
2 x Genoas (2002) and (2021)
Mechanical Systems:
This Steel Cutter is powered by a Yanmar 4JH3E 56hp diesel engine.(2002) The boat is shaft driven to a 3 bladed folding propeller .Fuel tank capacity is 380 litres in one mail tank and stowage for 10 external fuel cans .It has a cruising speed 7 knots and approximate max speed of 10.4 knots . the engine has completed 3165 hours as 1st August 2023. The engine has twin alternators.
The yacht is fitted with a 2016 Pordesk IKW 240V Genset new in 2021 with approx. 20 hours usage and a PUR Survivor water maker.
Electrical Systems:
The yacht has 4 x 12v 220AH gel batteries that were fitted new in April 2017 It has LED lighting and a number of 12v sockets throughout It has a VIctron 2kW battery charger and management system. There are 2 x 1kW movable solar panels and Victron triple MPPT charge controller and galvanic isolator. It has a 240v shore ring main system with RCD breakers, with fresh long run potential cords and new diodes, There is a pair of 100W swing mounted solar panels with a separate EP solar regulator and control display.... texte entier
Classic 50ft steel cutter for sale in Kent:
Artic Explorer is a classic 50ft steel cutter that is currently berthed in Chatham Marina. She was built in 1982 as an ocean going steel vessel with a cutter rig to a designed by Alan Mummery. This yacht has undergone an extensive refit over the past 4 years and is ready to go ocean sailing. It has 7 berths ,a comfortable living area and is powered by a Yanmar 4JH3E (2002) 56 HP diesel engine with a shaft drive to a 3 bladed folding propeller .This boat boasts all the navigation and deck gear you would expect for a ocean going vessel and is ready to set sail. This vessel is UK Vat paid and the owner is willing to delivery to Northern Europe or anywhere in the UK
Accommodation :
This 50ft steel cutter provides berths for up to six people in 3 cabins, with a double cabin to aft portside and a large single berth to starboard.
Forward is a large double berth with a large opening deck hatch which gives lots of light and makes the cabin feel very airy. The large concealed bar features a solid mahogany folding dining table with removable fiddles and sofa chairing.
The seating can also be used to provide two further berths. These berths have appropriate tailored lee-cloths. There is a roomy navigation area with navigators chair and full sized navigation station desk with both red and white lights and under-table storage for navigation books etc.
The galley is to port and has a seamless stainless steel worktop and has a pair of sinks with pressurised hot and cold water . Hot water heated by the engine and via a 240v immersion heater. There is a three burner stove with oven and grill.
There is a large heads compartment with marine toilet with a featured teak wash basin (new 2023) with shower and hot/cold mixer tap and multiple storage lockers and handholds throughout. The yacht has wide side decks which provide a real sense of safety when walking around deck.
The companion way steps lead up to the large and very secure cockpit which has a sold doghouse and lots of storage lockers.
Inventory :
Deck Equipment: 2 X 55lb CQR Anchors
60m of 10mm anchor chain
100m of anchor warp
Danforth Kedge Anchor with 40m of chain and 30m of warp
Electric Windlass
Danbuoys x 2
Horseshoe buoys x 2
Liferaft 6 person (new 2016 needs a service)
Fenders x 6
Mooring Warps x6
10ft Aluminium rib with 15hp outboard by separate negotiation
Navigation Equipment: Chart Plotter - Raymarine C90W with electronic charts European/Caribbean
AIS Receiver/Transponder -Raymarine
Depth - Raymarine
Speed/log -Raymarine
Wind -Raymarine
Autopilot - Raymarine
Fleming Ocean 60 wind vane
SSB (New SSB Antenna 2023)
VHF/DSC M323 ( New in 2022) with command mic
ST60 Iridium Go Satellite phone
New Mast Antenna
Furuno Radar
Safety Equipment: Fire Extinguishers x 4
Radar Reflector
EPIRB
Liferaft 6 person in need of a service
Jack Stays
Manual Bilge pump x 1
Electric Bilge pumps x 2
Keel:
Traditional long keel with tiller steering
History and Construction:
Artic Explorer Designed by Alan Mummery is a 50ft steel hull, cutter rig fin keel ocean going yacht. This yacht has had a major refit in the past four years getting her ready to complete in the next ARC. In 2017 the under went a full face lift including a re-paint of the hull and topsides, some new seacocks, new prop, new prop shaft new engine mounts and lots more. Unfortunately after all of this preparation for the adventure of a lifetime ill health is preventing the owner participating and hence why she is being advertised for sale
Mechanical :
Sails and Spars
The rigging on board this Alan Mummery Steel Cutter includes a twin spreader 15m aluminium mast, with new 2022 twin running backstays and spare masthead sheaves. There are heavy duty 'granny bars' at the mast and it has mast steps to the top of the mast. A heavy duty bowsprit features twin rollers and a steel rod bobstay; there is also a spinnaker and jockey pole with sheets and guys.
Nearly all of the running rigging is new, with ample spare ropes onboard, including Lewmar reefing lines. There are also 2016 Jackstays and Lazy jacks.
There is an extensive sail wardrobe which includes: two mainsails - one fully battened, three reef, slab reefed to cockpit; three genoas - one high cut and one in bright orange made in 2021 with Arctic Explorer name and logo on it ; staysail; two spare Yankee genoas; storm staysail (hank on); cruising chute; spinnaker with new sheets and guys
The deck of this Steel Cutter features a Heavy duty doghouse with reefing lines and main halyard led inside.
Winches:
Wilkins two-speed 26mm primary winches;
Harken 16mm secondary winches;
Lewmar winch for reefing lines in cockpit;
Barlow 26 mainsheet winch in cockpit;
Two mast winches; and one outhaul winch on boom. There are also a full suit of rope clutches
Sails:
Mainsail, Hood Thorn burrow - Slab (2002) Stack Pack, Fully Battened, 3 Reefs
Headsail Thorn burrow - Furling (2002)
Tri Sail (Unknown Year)
Cutter (2009)
Storm Jib (Unknown Year)
Spinnaker (Unknown Year)
Cruising Chute (2010)
2 x Genoas (2002) and (2021)
Mechanical Systems:
This Steel Cutter is powered by a Yanmar 4JH3E 56hp diesel engine.(2002) The boat is shaft driven to a 3 bladed folding propeller .Fuel tank capacity is 380 litres in one mail tank and stowage for 10 external fuel cans .It has a cruising speed 7 knots and approximate max speed of 10.4 knots . the engine has completed 3165 hours as 1st August 2023. The engine has twin alternators.
The yacht is fitted with a 2016 Pordesk IKW 240V Genset new in 2021 with approx. 20 hours usage and a PUR Survivor water maker.
Electrical Systems:
The yacht has 4 x 12v 220AH gel batteries that were fitted new in April 2017 It has LED lighting and a number of 12v sockets throughout It has a VIctron 2kW battery charger and management system. There are 2 x 1kW movable solar panels and Victron triple MPPT charge controller and galvanic isolator. It has a 240v shore ring main system with RCD breakers, with fresh long run potential cords and new diodes, There is a pair of 100W swing mounted solar panels with a separate EP solar regulator and control display.... texte entier
fermer la sélection
Données du bateau +
Données du bateau Classic 50FT Steel Cutter
Prix:
£ 99 950
(≈ € 116 706)
TVA incluse
Réf du bateau:
s231204
Modèle du bateau:
Classic 50FT Steel Cutter
Constructeur:
Type de bateau:
voilier
Catégorie de bateau:
yacht à voile
Catégorie:
bateau d'occasion
Année de construction:
1982
Lieu:
Grande Bretagne, Chatham Marina, Kent
Matériau de la coque:
bateau en acier
Données techniques
Longueur:
15,24 m (50 pieds)
Largeur:
3,66 m
Moteur:
Yanmar 4JH3E (2002)
Puissance du moteur:
56 cv (41 kW)
Carburant:
diesel
fermer la sélection
Publicité / service
Équipement+
Acheter Classic 50FT Steel Cutter - équipements yacht à voile - à vendre
Navigationautopilote, plotter, radar, VHF
Equipement technique
chargeur de batteries
Sécurité
canot de sauvetage, EPIRB, pompe de cale - électrique, pompe de cale - manuelle
Equipement du pont
amortisseur
Equipement intérieur
barbecue, robinet
Voiles
spinnaker
fermer la sélection
Contact-
Classic 50FT Steel Cutter - information sans obligation - yacht à voile
pf-21790
N'oubliez pas d’indiquer au propriétaire du bateau que vous avez trouvé cette offre sur Yachtall.
Contact:
Band of Boats
Network Yacht Brokers Kent
Chatham Maritime Marina, Leviathan Way Chatham
ME4 4LP Kent
Grande Bretagne
Téléphone:
afficher
Langues:
anglais, français
Client sur yachtall.com depuis 4 ans
fermer la sélection
Acheter un bateau:
Custom built/Eigenbau bateaux yachts à voile voiliers à vendre voiliers Grande Bretagne bateaux d’occasion bateaux d’occasion Custom built/Eigenbau bateaux en acier
Custom built/Eigenbau bateaux yachts à voile voiliers à vendre voiliers Grande Bretagne bateaux d’occasion bateaux d’occasion Custom built/Eigenbau bateaux en acier
Autres bateaux (comme Classic 50FT Steel Cutter) - pour acheter et à vendre
Custom built Caroff
Voilier / yacht à voile: Custom built/Eigenbau, bateau d'occasion, bateau en acierLongueur x largeur: 14,17 m x 4,60 m, 14,17 x 4,60 m construit: 1981, cabines: 3
Moteur: Yanmar, 85 cv (63 kW), diesel
€ 79 200
Lieu: Espagne, Valencia
1981
Société: Band of Boats
Prix: € 79 200, TVA incluse
Custom built Foiler 50
Voilier / trimaran à voile: Custom built/Eigenbau, bateau d'occasionLongueur x largeur: 15,24 m x 11,89 m, 15,24 x 11,89 m construit: 1983
€ 70 000
Lieu: Saint-Martin (néerlandais), Caribbean
1983
Société: Band of Boats
Prix: € 70 000, HT
Steel Sailboat 50
Voilier / yacht à voile: Custom built/Eigenbau, bateau d'occasion, bateau en acierLongueur x largeur: 15,24 m x 4,30 m, 15,24 x 4,30 m construit: 1991
Moteur: TMD41A, 150 cv (110 kW), diesel
kr. 1 550 000
Lieu: Danemark, Svendborg
1991
Société: Band of Boats
Prix: kr. 1 550 000 (≈ € 207 851), HT
Custom PLAN Caroff
Voilier / yacht à voile: Custom built/Eigenbau, bateau d'occasionLongueur x largeur: 14,17 m x 4,60 m, 14,17 x 4,60 m construit: 1981, cabines: 3
Moteur: Yanmar, 85 cv (63 kW)
€ 69 000
Lieu: Espagne, Empuriabrava
1981
Société: Band of Boats
Prix: € 69 000, TVA incluse
Ces voiliers pourraient également vous intéresser
Custom built Schooner (14,90 m) Aluminium 52 ft Centerboard (15,80 m) Ketch Galeasen Jutta (16,20 m) Lansart 47 (14,76 m) 50 Feet Aluminium Catamaran (14,95 m) Rinaldi ARIA 142 (14,20 m) Solent Arthur ROBB 54 (16,28 m) Gulet Caicco ECO 310 (14,95 m) Gulet Caicco ECO 155 (15 m) Van de Stadt 51 (15,53 m) Catamaran 15 M (15 m) Custom built 50' Yawl (15,24 m)Quelle version voulez-vous voir ?
Envoyer une demande
Classic 50FT Steel Cutter, constr. 1982
Contact:
Band of Boats