Añadir a mi lista
Eliminar de mi lista
boatDetail
boatDetail
0
bid=s232391
bid=s232391
s232391
5
Gulfstar 44 (velero) - en venta
velero / yate de crucero, yate de vela, barco de ocasiónImágenes
1 / 7
▶
▶
imágenes
imprimir
compartir
Descripción +
- Stock #388564 -
Take alook at this hard-to-find sloop! Snap this one up before it is gone.
Are you in the market for a cruising sailboat? Look no further! This 1982 Gulfstar 44 is a beautiful boat that has been maintained and is in great condition, the owner confirms.
With a length of 44' 8" and a beam of 13' 2", this center cockpit sailboat offers plenty of room for relaxation and enjoyment on the water. Powered by a Perkins 4-108 diesel engine, this boat provides 10 nautical miles per gallon at 5 to 6 knots cruising with a custom-made Gori 23x13 folding propeller.
Equipped with 280 watts of solar power and a 400W Airgen wind generator, you'll have plenty of power options while out on the water.
With 2 cabins and 2 heads, this boat is perfect for those looking for comfort and style while cruising.
So, what are you waiting for? Come check out this beautiful Gulfstar 44 today!
I acquired Sea Hawk in 1982 and over the years made many improvements to her as outlined below:
The boat had suffered some below water hull damage during Hurricane Bob in 1991. All damaged hull fiberglass was removed and replaced using West Epoxy and biaxial fiberglass, better materials than used in her construction.
The bottom had been peeled when acquired and I had the whole bottom and keel covered with 21 oz biaxial fiberglass cloth and west epoxy and then sealed with Interlux Inter Portect 200E so blistering will never be a problem.
A new Rudder and Skeg were made using waterproof plywood covered with Biaxial fiberglass cloth and west epoxy to replace the damaged components.
The propeller shaft which had a very slight bend in the taper region, and the propeller were replaced.
The bent 3 blade fixed propeller was replaced by a 2 blade geared folding GORI propeller, custom modified over the next two years to be a 23 x 13 propeller which provides excellent cruising mileage of 10 nmpg, generally unheard of in a 26,000 pound sailboat.
The propeller shaft is spiral wrapped with fiberglass roving and west Epoxy to provide a non chipping coating for the bottom paint to adhere to. A new zinc collar is also attached to the shaft.
The Cutlass bearing has been recently replaced so no maintenance in this regard will be needed for about 10 years of normal use.
The original design skeg bolted on by five studs in a row, which failed was replaced for over $20,000, by a superior design and materials skeg with two larger diameter bolts to the side and 3 others in line, and attached from the inside so the rudder does not have to be dropped to remove the skeg, should that ever be necessary. The new skeg has only a partial sesason of use since installed.
The spider around the rudder post was also strengthened when the new skeg was installed. The steering cables to the pedestal have also been replaced.
The aft end of the keel has been extended by about 15" to allow for good hydrodynamic fairing instead of the as built thick rounded trailing edge, to improve speed and balance of the boat under sail.
The bottom paint is Interlux Micron 66, the best available ablative bottom paint from Interlux for use in salt water. A fresh coat will be applied before launching for the purchaser..
The Perkins 4-108 engine has very few hours on it for a boat of this age since I was able to sail it in and out of the harbor in Cotuit MA. The total hours are well under 2500. The oil was changed at the end of each season with Mobil Delvac or synthetic Mobil oil since new. The transmission was completely filled to prevent corrosion at haul out and drained to the correct use level when launched in the spring.
The interior teak bulkheads and panels have been coated with West Epoxy coating resin to eliminate the need to re oil the teak every year. The solid teak wood doors have also been sealed with coating epoxy and then varnished with West System varnish for a beautiful finish.
The aft cabin cushions have been replaced with 6" thick foam to provide a more comfortable sleeping surface. The forward Vee Birth cushions and covers have been replaced by 5" thick foam. All cushion covers are made from machine washable fabrics.
A refrigeration unit was added to the ice box after the boat was equipped with a 285 watt solar panel which more than supplies the electricity needs of the boat in sunny weather. Ice cubes can be made under the cold air supply from the refrigeration unit.
A wind generator mounted at the stern is also supplied to augment the solar panel output on cloudy windy days.
The original Signet instruments are available but have been replaced by Silva / Nexus instruments with much improved displays. Fixed and hand held VHF radios are supplied.
The Furuno radar display is mounted on a custom bracket that allows the display to be seen from the chart table or pushed up through the galley overhead hatch to be seen from the cockpit.
A new, one season ago, maximum size varnished cockpit teak table has been made and fitted, which is 60% larger than the original cockpit table, which is also available.
The teak cap rail around the cockpit has just been refinished, and all exterior teak has been kept varnished since the boat was new.
A large dodger extending back to the pedestal is included along with a smaller dodger and a Bimini which was used by the original owner. I'm the second owner.
The mast, spreaders and boom have been maintained with Awlgrip two part polyurethane paint since new.
The brackets for attaching the lower spreaders to the mast were reinforced and structurally improved after one of them failed under sail.
The top plates on the turning blocks were replaced with stronger and thicker plates to improve the free running of the sheaves.
The bolts holding the side rail tracks were replaced in way of normal trimming car locations with superior strength stainless steel after one of the heads on the original bolts snapped off due to hidden corrosion cracking.
The standing rigging was inspected with the mast down since the boat was hauled and found to be in good
condition, in the most recent survey, and the boat has never been struck by lightening. The advertised sale price includes replacing the standing rigging if wanted or an allowance (of about $7k) will be made for those not wanting to have the rig replaced.
Sails are what power a sailboat! Since great performance was desired, the original sails, that come with the boat, were replaced by North Sails Main and 2 152% genoas.
These sails have powered the boat to numerous New England race wins including the Venona prize for the "Round the Vineyard race" which we won both in class and overall including all classes based on our PHRF corrected time ?? Other race wins include the Buzzards Bay Regatta and several Whalers races around Block Island.
Also installed is a removable inner headstay about 6" aft of the Harken roller furler which replaced the original Hood roller furler, and the replaced headsay, for which two hank on sails are included one about 120% and one a storm sail.
Full spinnaker gear including an 18' spinnaker pole, mast track, topping lift and sheets are supplied along with a working spinnaker, (not measured for racing).
A 45 pound CQR plow anchor and 14' 3/8" stainless steel anchor chain and rode are the normal anchoring gear and a 22 pound Danforth anchor, chain and rode is also supplied.
We are looking for people all over the country who share our love for boats. If you have a passion for our product and like the idea of working from home, please visit Careeers [dot] (website in contact data) to learn more.
This listing has now been on the market a couple months. Please submit any and all offers today!
Reason for selling is no longer using.
At Pop Yachts, we will always provide you with a TRUE representation of every vessel we market. We encourage all buyers to schedule a survey for an independent analysis. Any offer to purchase is ALWAYS subject to satisfactory survey results. Contact us for a free BoatHistoryReport report on this vessel. We pay upfront for a report on every vessel possible, and we provide this peace of mind to our buyers at no charge and with no commitment. All you have to do is ask!
You have questions? We have answers. Call us at 001 941-404-4437 to discuss this boat.
Selling your boat has never been easier. At Pop Yachts, we literally sell thousands of units every year all over the country. Call 001 855-218-2805 and we'll get started selling your boat today.
Take a look at ALL ***ORIGINAL PICTURES*** of this vessel on our main (e-mail in contact data). We appreciate that you took your time to look at our advertisement and we look forward to speaking with you!... texto completo
Take alook at this hard-to-find sloop! Snap this one up before it is gone.
Are you in the market for a cruising sailboat? Look no further! This 1982 Gulfstar 44 is a beautiful boat that has been maintained and is in great condition, the owner confirms.
With a length of 44' 8" and a beam of 13' 2", this center cockpit sailboat offers plenty of room for relaxation and enjoyment on the water. Powered by a Perkins 4-108 diesel engine, this boat provides 10 nautical miles per gallon at 5 to 6 knots cruising with a custom-made Gori 23x13 folding propeller.
Equipped with 280 watts of solar power and a 400W Airgen wind generator, you'll have plenty of power options while out on the water.
With 2 cabins and 2 heads, this boat is perfect for those looking for comfort and style while cruising.
So, what are you waiting for? Come check out this beautiful Gulfstar 44 today!
I acquired Sea Hawk in 1982 and over the years made many improvements to her as outlined below:
The boat had suffered some below water hull damage during Hurricane Bob in 1991. All damaged hull fiberglass was removed and replaced using West Epoxy and biaxial fiberglass, better materials than used in her construction.
The bottom had been peeled when acquired and I had the whole bottom and keel covered with 21 oz biaxial fiberglass cloth and west epoxy and then sealed with Interlux Inter Portect 200E so blistering will never be a problem.
A new Rudder and Skeg were made using waterproof plywood covered with Biaxial fiberglass cloth and west epoxy to replace the damaged components.
The propeller shaft which had a very slight bend in the taper region, and the propeller were replaced.
The bent 3 blade fixed propeller was replaced by a 2 blade geared folding GORI propeller, custom modified over the next two years to be a 23 x 13 propeller which provides excellent cruising mileage of 10 nmpg, generally unheard of in a 26,000 pound sailboat.
The propeller shaft is spiral wrapped with fiberglass roving and west Epoxy to provide a non chipping coating for the bottom paint to adhere to. A new zinc collar is also attached to the shaft.
The Cutlass bearing has been recently replaced so no maintenance in this regard will be needed for about 10 years of normal use.
The original design skeg bolted on by five studs in a row, which failed was replaced for over $20,000, by a superior design and materials skeg with two larger diameter bolts to the side and 3 others in line, and attached from the inside so the rudder does not have to be dropped to remove the skeg, should that ever be necessary. The new skeg has only a partial sesason of use since installed.
The spider around the rudder post was also strengthened when the new skeg was installed. The steering cables to the pedestal have also been replaced.
The aft end of the keel has been extended by about 15" to allow for good hydrodynamic fairing instead of the as built thick rounded trailing edge, to improve speed and balance of the boat under sail.
The bottom paint is Interlux Micron 66, the best available ablative bottom paint from Interlux for use in salt water. A fresh coat will be applied before launching for the purchaser..
The Perkins 4-108 engine has very few hours on it for a boat of this age since I was able to sail it in and out of the harbor in Cotuit MA. The total hours are well under 2500. The oil was changed at the end of each season with Mobil Delvac or synthetic Mobil oil since new. The transmission was completely filled to prevent corrosion at haul out and drained to the correct use level when launched in the spring.
The interior teak bulkheads and panels have been coated with West Epoxy coating resin to eliminate the need to re oil the teak every year. The solid teak wood doors have also been sealed with coating epoxy and then varnished with West System varnish for a beautiful finish.
The aft cabin cushions have been replaced with 6" thick foam to provide a more comfortable sleeping surface. The forward Vee Birth cushions and covers have been replaced by 5" thick foam. All cushion covers are made from machine washable fabrics.
A refrigeration unit was added to the ice box after the boat was equipped with a 285 watt solar panel which more than supplies the electricity needs of the boat in sunny weather. Ice cubes can be made under the cold air supply from the refrigeration unit.
A wind generator mounted at the stern is also supplied to augment the solar panel output on cloudy windy days.
The original Signet instruments are available but have been replaced by Silva / Nexus instruments with much improved displays. Fixed and hand held VHF radios are supplied.
The Furuno radar display is mounted on a custom bracket that allows the display to be seen from the chart table or pushed up through the galley overhead hatch to be seen from the cockpit.
A new, one season ago, maximum size varnished cockpit teak table has been made and fitted, which is 60% larger than the original cockpit table, which is also available.
The teak cap rail around the cockpit has just been refinished, and all exterior teak has been kept varnished since the boat was new.
A large dodger extending back to the pedestal is included along with a smaller dodger and a Bimini which was used by the original owner. I'm the second owner.
The mast, spreaders and boom have been maintained with Awlgrip two part polyurethane paint since new.
The brackets for attaching the lower spreaders to the mast were reinforced and structurally improved after one of them failed under sail.
The top plates on the turning blocks were replaced with stronger and thicker plates to improve the free running of the sheaves.
The bolts holding the side rail tracks were replaced in way of normal trimming car locations with superior strength stainless steel after one of the heads on the original bolts snapped off due to hidden corrosion cracking.
The standing rigging was inspected with the mast down since the boat was hauled and found to be in good
condition, in the most recent survey, and the boat has never been struck by lightening. The advertised sale price includes replacing the standing rigging if wanted or an allowance (of about $7k) will be made for those not wanting to have the rig replaced.
Sails are what power a sailboat! Since great performance was desired, the original sails, that come with the boat, were replaced by North Sails Main and 2 152% genoas.
These sails have powered the boat to numerous New England race wins including the Venona prize for the "Round the Vineyard race" which we won both in class and overall including all classes based on our PHRF corrected time ?? Other race wins include the Buzzards Bay Regatta and several Whalers races around Block Island.
Also installed is a removable inner headstay about 6" aft of the Harken roller furler which replaced the original Hood roller furler, and the replaced headsay, for which two hank on sails are included one about 120% and one a storm sail.
Full spinnaker gear including an 18' spinnaker pole, mast track, topping lift and sheets are supplied along with a working spinnaker, (not measured for racing).
A 45 pound CQR plow anchor and 14' 3/8" stainless steel anchor chain and rode are the normal anchoring gear and a 22 pound Danforth anchor, chain and rode is also supplied.
We are looking for people all over the country who share our love for boats. If you have a passion for our product and like the idea of working from home, please visit Careeers [dot] (website in contact data) to learn more.
This listing has now been on the market a couple months. Please submit any and all offers today!
Reason for selling is no longer using.
At Pop Yachts, we will always provide you with a TRUE representation of every vessel we market. We encourage all buyers to schedule a survey for an independent analysis. Any offer to purchase is ALWAYS subject to satisfactory survey results. Contact us for a free BoatHistoryReport report on this vessel. We pay upfront for a report on every vessel possible, and we provide this peace of mind to our buyers at no charge and with no commitment. All you have to do is ask!
You have questions? We have answers. Call us at 001 941-404-4437 to discuss this boat.
Selling your boat has never been easier. At Pop Yachts, we literally sell thousands of units every year all over the country. Call 001 855-218-2805 and we'll get started selling your boat today.
Take a look at ALL ***ORIGINAL PICTURES*** of this vessel on our main (e-mail in contact data). We appreciate that you took your time to look at our advertisement and we look forward to speaking with you!... texto completo
cerrar la selección
Datos de barco +
Datos de barco Gulfstar 44
Precio:
$ 87.800
(≈ € 81.949)
IVA excluído
ID del barco:
s232391
Modelo de barco:
Gulfstar 44
Fabricante:
Tipo de barco:
velero
Categoría:
yate de crucero, yate de vela
Categoría:
barco de ocasión
Año de fabricación:
1982
Amarre:
Estados Unidos, Massachusetts, Cotuit
Camarotes / camas:
3 / 1
Material del casco:
PRFV/plástico
Color del casco:
blanco
Datos técnicos
Eslora:
13,41 m (44 pies)
Manga:
4,02 m
Calado aéreo:
17,07 m
Baños:
2
Motor:
Perkins Sabre
Potencia del motor:
50 hp (37 kW)
Combustible:
diesel
Horas del motor:
aprox. 2.100
Velocidad de crucero:
5 kn
Velocidad máx.:
7 kn
Tanque de combustible:
303 l
cerrar la selección
Anuncios / servicio
Equipamiento+
Comprar Gulfstar 44 - equipamiento yate de crucero - velero en venta
Navegacióncompás (Mounted Above Wheel), GPS, radar (Furuno Mounted On Aft Pole), radio VHF
Equipamiento técnico
ancla, batería (4 House + 1 Starting), generador
Seguridad
bomba de achique
Equipamiento de cubierta
bimini-top (Extra Large Dodger 5 Removable Windows With Roll Up Straps)
Equipamiento interior
horno (3 Burner; SS)
Velas
blister, génova, spinnaker, tormentín, vela mayor (North With 2 Full And 2 Partial Length Battens)
Otro equipamiento
mesa en la cabina
cerrar la selección
Contacto-
Gulfstar 44 - informarse - sin compromiso - yate de crucero
pf-8903
Por favor, dígale al propietario que ha encontrado esta oferta en Yachtall.
Contacto:
POP Yachts International
Sr. Scott McNally
5717 Bessie Drive
34233 Sarasota
Estados Unidos
Teléfono:
mostrar
Fax:
mostrar
Idiomas:
inglés
www.popyachts.com
Desde hace 13 años en yachtall.com
cerrar la selección
Comprar un barco:
Gulfstar 44 Gulfstar Yachts barcos yates de crucero veleros comprar veleros Estados Unidos barcos de ocasión barcos de ocasión Gulfstar Yachts
Gulfstar 44 Gulfstar Yachts barcos yates de crucero veleros comprar veleros Estados Unidos barcos de ocasión barcos de ocasión Gulfstar Yachts
Vender o comprar otros barcos (como Gulfstar 44)
Gulfstar 41
Velero / yate de vela: Gulfstar Yachts, barco de ocasión, PRFV/plásticoEslora x manga: 12,50 m x 3,66 m, 12,50 x 3,66 m año de fab.: 1974, camarotes: 2
Motor: Perkins Sabre, 50 hp (37 kW), diesel
$ 59.500
Amarre: Estados Unidos, Carolina del Norte, New Bern
1974
Empresa: POP Yachts International
Precio: $ 59.500 (≈ € 55.535), IVA excluído
Gulfstar 44
Velero / balandra: Gulfstar Yachts, barco de ocasión, PRFV/plásticoEslora x manga: 13,41 m x 4,18 m, 13,41 x 4,18 m año de fab.: 1972, camarotes: 2
Motor: Lehman, 120 hp (88 kW), diesel
$ 28.000
Amarre: Estados Unidos, Rhode Island, Warwick
1972
Empresa: POP Yachts International
Precio: $ 28.000 (≈ € 26.135), IVA excluído
Gulfstar 44
Velero / velero de motor: Gulfstar Yachts, barco de ocasión, PRFV/plásticoEslora x manga: 13,41 m x 4,08 m, 13,41 x 4,08 m año de fab.: 1973, camarotes: 2
Motor: Perkins Sabre, 160 hp (118 kW), diesel
$ 102.000
Amarre: Estados Unidos, Florida, Key West
1973
Empresa: POP Yachts International
Precio: $ 112.800 $ 102.000 (≈ € 95.203), IVA excluído
Whitby Boat Works 42
Velero / queche: Whitby Boat Works Ltd., barco de ocasión, PRFV/plásticoEslora x manga: 12,80 m x 3,96 m, 12,80 x 3,96 m año de fab.: 1975, camarotes: 3
Motor: Ford, 80 hp (59 kW), diesel
$ 100.000
Amarre: México, Ensenada, Baja California Sur
1975
Empresa: POP Yachts International
Precio: $ 100.000 (≈ € 93.336), IVA excluído
Estos veleros pudieran gustarle
Gulfstar 47 (14,30 m) Lagoon 42 (12,80 m) Comar Genesi 43 (13,10 m) Bénéteau First 42 (13,08 m) Hunter 450 Passage (13,41 m) Lagoon 42 (12,79 m) Gillissen 1260 Ketch Rig (12,60 m) Dufour 460 Grand Large (14,15 m) Bénéteau First 45F5 Fast Boatlots of Sailssolar (14,20 m) Jeanneau Sun Odyssey 469 (14,05 m) Dufour 460 Grand Large (13,50 m) Bavaria Vision 40 (12,70 m)¿Qué versión desea ver?
Enviar solicitud
Gulfstar 44, fabr. 1982
Contacto:
POP Yachts International
Sr. Scott McNally
Sr. Scott McNally